manualshive.com logo in svg

Cisco UCS B200 M5, Installation And Service Note

Share
Download
Cisco UCS B200 M5 Installation And Service Note Download Page 11

C H A P T E R  

1

Overview

This chapter contains the following sections:

•

Cisco UCS B200 M5 Blade Server, page 1

•

External Features Overview, page 2

•

Drive Bays, page 5

•

Graphics Processing Unit , page 5

Cisco UCS B200 M5 Blade Server

The Cisco UCS B200 M5 is a density-optimized, half-width blade server that supports two CPU sockets for
the Intel Xeon Processor Scalable Family of CPUs. The server supports the following features:

•

24 DDR4 DIMMs

•

1 front mezzanine module (storage or graphics processing unit (GPU))

•

1 modular LAN on motherboard (mLOM) module

•

1 rear mezzanine module (I/O or GPU)

•

A mini-storage module with dual SATA 3.0 M.2 cards or secure digital (SD) cards

You can install up to eight UCS B200 M5 blade servers in a UCS 5108 chassis, mixing with other models of
Cisco UCS blade servers in the chassis if desired.

Cisco UCS B200 M5 Blade Server Installation and Service Note    

1

Summary of Contents for UCS B200 M5











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands