manualshive.com logo in svg

Cisco UCS B200 M5, Installation And Service Note

Share
Download
Cisco UCS B200 M5 Installation And Service Note Download Page 52

NVIDIA P6 Graphics Processing Unit

The NVIDIA P6 graphics processing unit (GPU) card provides graphics and computing capabilities to the
server. There are two supported versions of the NVIDIA P6 GPU card:

•

UCSB-GPU-P6-F can be installed only in the front mezzanine slot of the server. For installation
instructions, see

Installing an NVIDIA GPU Card in the Front of the Server, on page 43

.

•

UCSB-GPU-P6-R can be installed only in the rear mezzanine slot (slot 2) of the server. For installation
instructions, see

Installing an NVIDIA GPU Card in the Rear of the Server, on page 46

.

The following figure shows the installed NVIDIA P6 GPU in the front and rear mezzanine slots.

Figure 19: NVIDIA GPU Installed in the Front and Rear Mezzanine Slots

Rear GPU

2

Front GPU

1

-

Custom standoff screw

3

   Cisco UCS B200 M5 Blade Server Installation and Service Note

42

Servicing a Blade Server

NVIDIA P6 Graphics Processing Unit

Summary of Contents for UCS B200 M5











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands