manualshive.com logo in svg

Cisco UCS B200 M5, Installation And Service Note

Share
Download
Cisco UCS B200 M5 Installation And Service Note Download Page 13

The removable drives also have LEDs indicating hard disk access activity and disk health.

Table 1: Blade Server LEDs

Description

Color

LED

Power off.

Off

Power

Main power state. Power is supplied to all server
components and the server is operating normally.

Green

Standby power state. Power is supplied only to the service
processor of the server so that the server can still be
managed.

The front-panel power button is disabled by
default. It can be re-enabled through Cisco UCS
Manager. After it's enabled, if you press and
release the front-panel power button, the server
performs an orderly shutdown of the 12 V main
power and goes to standby power state. You
cannot shut down standby power from the
front-panel power button. See the Cisco UCS
Manager Configuration Guides for information
about completely powering off the server from
the software interface.

Note

Amber

None of the network links are up.

Off

Link

At least one network link is up.

Green

Power off.

Off

Health

Normal operation.

Green

Minor error.

Amber

Critical error.

Blinking Amber

Blinking is not enabled.

Off

Blue locator button and LED

Blinking to locate a selected blade

—

If the LED is not

blinking, the blade is not selected. You can control the
blinking in UCS Manager or by using the blue locator
button/LED.

Blinking blue 1
Hz

Inactive.

Off

Activity

(Disk Drive)

Outstanding I/O to disk drive.

Green

Cisco UCS B200 M5 Blade Server Installation and Service Note    

3

Overview

LEDs

Summary of Contents for UCS B200 M5











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands