manualshive.com logo in svg

Cisco UCS B200 M5, Installation And Service Note

Share
Download
Cisco UCS B200 M5 Installation And Service Note Download Page 37

Procedure

Step 1

Using a #1 Phillips-head screwdriver, loosen the screw securing the M.2 card to the top of the M.2 mini-storage
module.

Step 2

Pull the M.2 card from the module connector.

Step 3

Repeat these steps to remove the M.2 card from the bottom of the M.2 mini-storage module.

Installing the SATA 3.0 M.2 Cards

This task describes how to install the SATA 3.0 M.2 cards into the M.2 mini-storage module.

Procedure

Step 1

Align the gold fingers on the M.2 card with the module connector on the top of the M.2 mini-storage module,
and then fully push the M.2 card into the module connector.

Step 2

Using a #1 Phillips-head screwdriver, tighten the provided screw to secure the M.2 card to the M.2 mini-storage
module.

Step 3

Repeat these steps to install the M.2 card on the bottom of the M.2 mini-storage module.

Figure 9: Installing the SATA 3.0 M.2 Cards

Cisco UCS B200 M5 Blade Server Installation and Service Note    

27

Servicing a Blade Server

Installing the SATA 3.0 M.2 Cards

Summary of Contents for UCS B200 M5











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands