manualshive.com logo in svg

Cisco UCS B200 M5, Installation And Service Note

Share
Download
Cisco UCS B200 M5 Installation And Service Note Download Page 64

You obtain the licenses that are served by the GRID License Server from the NVIDIA Licensing Portal as
downloadable license files, which you install into the GRID License Server via its management interface. See
the following figure.

Figure 26: GRID Licensing Architecture

There are three editions of GRID licenses that enable three different classes of GRID features. The GRID
software automatically selects the license edition based on the features that you are using. See the following
table.

Table 3: GRID Licensing Editions

GRID Features

GRID License Edition

Virtual GPUs for business desktop computing

GRID Virtual GPU (vGPU)

Virtual GPUs for mid-range workstation computing

GRID Virtual Workstation

Virtual GPUs for high-end workstation computing

Workstation graphics on GPU pass-through

GRID Virtual Workstation - Extended

   Cisco UCS B200 M5 Blade Server Installation and Service Note

54

NVIDIA Licensing Information

NVIDIA GRID License Server Overview

Summary of Contents for UCS B200 M5











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands