manualshive.com logo in svg

Cisco UCS B200 M5, Installation And Service Note

Share
Download
Cisco UCS B200 M5 Installation And Service Note Download Page 33

The noprobe values depend on the number of drives. For example, to install RHEL 6.5 on a RAID
5 configuration with three drives, enter:

Linux dd blacklist=isci blacklist=ahci nodmraid noprobe=ata1 noprobe=ata2

Note

Step 9

Press

Enter

.

The prompt asks whether you have a driver disk.

Step 10

Use the arrow key to choose

Yes

, and then press

Enter

.

Step 11

Choose

fd0

to indicate that you have a disk with the driver on it.

Step 12

Do one of the following actions:

•

If you prepared the

dud.img

file on a physical thumb drive, insert the thumb drive to the target server

and then press

Enter

.

•

If you mapped the

dud.img

(or .iso) file as a virtual disk, choose the location of the virtual disk.

The installer locates and loads the driver for your device. The following message appears:

Loading megasr driver...

Step 13

Follow the RHEL installation procedure to complete the installation.

Step 14

Reboot the target server.

Installing the SUSE Linux Enterprise Server Driver

For the specific supported OS versions, see the

Hardware and Software Compatibility Matrix

for your server

release.

This topic describes the fresh installation of the SLES driver on systems that have the embedded MegaRAID
stack.

If you use an embedded RAID controller with Linux, both the pSATA and the sSATA controller must be
set to

LSI SW RAID

mode.

Note

Before You Begin

Before you install this driver on the sSATA embedded controller, you must configure a RAID drive group.

To access the configuration utility, open the BIOS Setup Utility, go to the

Advanced

tab, and then choose

the utility instance for the sSATA embedded controller:

LSI Software RAID Configuration Utility (sSATA)

.

Procedure

Step 1

Prepare the

dud.img

(or .iso) file using one of the following methods:

•

To install from physical disk, use the procedure in

Preparing Physical Thumb Drive for Linux, on page

21

, then continue with step 4.

•

To install from

virtual

disk, download the Cisco UCS B-Series drivers

’

ISO, as described in

Downloading

the MegaSR Drivers, on page 18

, then continue with the next step.

Cisco UCS B200 M5 Blade Server Installation and Service Note    

23

Servicing a Blade Server

Installing LSI MegaSR Drivers For Windows and Linux

Summary of Contents for UCS B200 M5











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands