Cisco StadiumVision SV-4K Deployment Manual Download

Page: 12 / 76

Ports on the SV-4K Media Player

Figure 2. SV-4K Front Panel

Table 4. SV-4K Front Panel Port Descriptions

Port Name

Usage

Description

Audio

Required only for connections that do not support
audio, such as HDMI-to-DVI connections from
SV-4K to the TV.

3.5 mm female audio
connector for analog stereo
signal.

The SV-4K does not have an internal infrared
receiver. You must use the included IR extender
cable to support an IR remote.

3.5 mm infrared in/out.

Serial

Connect to TV serial port for control of the TV via
RS-232 commands.

RS-232 serial interface with
male DE-9 connector. This
connection is used for
TV control.

USB

Not supported.

USB 2.0 port

The analog audio out port is designed to drive line-level impedances in the higher Ohm range, such as

for commercial grade speaker systems. Headphones are typically just a few Ohms and not recommended
for use with this port.

4 of 68

Summary of Contents for StadiumVision SV-4K










































































Search results

Summary of Contents for StadiumVision SV-4K

Reviews:

Related manuals for StadiumVision SV-4K

Brands by name

Popular brands

Cisco StadiumVision SV-4K, Deployment Manual

Search results

Summary of Contents for StadiumVision SV-4K

Reviews:

Related manuals for StadiumVision SV-4K

Brands by name

Popular brands