Cisco SCE 1000 2xGBE Installation And Configuration Manual Download Page 51

Page: 51 / 133

Chapter 4 Installation and Maintenance

Power Supply Overview

Cisco SCE 1000 2xGBE Installation and Configuration Guide

OL-7821-05

4-11

The other side of the grounding cable must be connected to the site equivalent of the AC earth.

Figure

4-10: Grounding the Unit (AC)

Figure

4-11: Grounding the Unit (DC)

This completes the procedure for installing the

SCE 1000

chassis. Proceed to the next section,

Connecting to the Power Supply, to continue the installation.

Power Supply Overview

The

SCE 1000

is available in two power options:

•

Dual line feed AC power —

SCE 1000

is shipped with two appropriate AC power supply

cords.

•

Dual line feed DC power — requires appropriate cables (hex or loop connectors) (see

Reconnecting DC-Input Power Supply Unit

(on page

4-18

)).

Summary of Contents for SCE 1000 2xGBE






































































































































Search results

Summary of Contents for SCE 1000 2xGBE

Reviews:

Related manuals for SCE 1000 2xGBE

Brands by name

Popular brands

Cisco SCE 1000 2xGBE, Installation And Configuration Manual

Search results

Summary of Contents for SCE 1000 2xGBE

Reviews:

Related manuals for SCE 1000 2xGBE

Brands by name

Popular brands