Cisco SCE 1000 2xGBE Installation And Configuration Manual Download Page 118

Page: 118 / 133

Chapter 8 Troubleshooting

Problem Solving Using a Subsystems Approach

Cisco SCE 1000 2xGBE Installation and Configuration Guide

8-10

OL-7821-05

Faulty power supply.

If the system still fails to come up when the
power supply is connected to a different power
source with a new power cable, the power
supply unit is probably faulty. Contact a service
representative.

Table

8-4 Power

Supply

LEDs

LED Label

Color

State

Function

IN Green

The

input

voltage

is in the required range.

Off

The input voltage is not in the required
range.

Green

The output voltage is in the required range
(between 11.9 and 12.1 VDC).

Off

The output voltage is not within the
required range (is greater than 12.1 VDC or
less than 11.9 VDC).

Power A/B (front panel)

Green

Steady

Corresponding power supply unit is present
and functioning normally.

Red

Steady

Corresponding power supply unit present,
but malfunctioning.

Off

Corresponding power supply unit is either
not present or has failed.

Troubleshooting the Firmware Package Installation

Check the following to help isolate a problem in the installation of the firmware package.

Problems related to the installation of the firmware package could be any of the following:

•

File not found in the expected location

•

Wrong file type.

•

Device to which the file is to be extracted is full.

Summary of Contents for SCE 1000 2xGBE






































































































































Search results

Summary of Contents for SCE 1000 2xGBE

Reviews:

Related manuals for SCE 1000 2xGBE

Brands by name

Popular brands

Cisco SCE 1000 2xGBE, Installation And Configuration Manual

Search results

Summary of Contents for SCE 1000 2xGBE

Reviews:

Related manuals for SCE 1000 2xGBE

Brands by name

Popular brands