Cisco SCE 1000 2xGBE Installation And Configuration Manual Download Page 96 | Manualshive

Page: 96 / 133

background image

Chapter 6 Cabling the Line Ports and Completing the Installation

Loading and Activating a Service Control Application

Cisco SCE 1000 2xGBE Installation and Configuration Guide

6-8

OL-7821-05

In oversized packets: 0
Out total octets: 93*2^32+1022342538
Out unicast packets: 858086051
Out non unicast packets: 0
Out packets discarded: 0

You are now ready to continue to the next stage, loading and activating an Service Control
Application.

Loading and Activating a Service Control Application

The

SCE 1000

platform provides the basic functionalities of Service Control analysis and

enforcement. A Service Control solution requires that a Service Control application be loaded into
the platform, to take advantage of the unique SCE platform capabilities.

Loading and activating an application includes the following stages:

•

Downloading the application provided as an SLI file to the

SCE 1000

disk.

•

Activating the application.

•

Configuring the application.

The detailed procedure of how to perform these operations is not specified and described in this
manual. For further details, refer to the following documentation:

•

Service Control Application for Broadband User Guide

•

Service Control Application for Broadband Reference Guide

«
...
94
95
96
97
98
...
»

Summary of Contents for SCE 1000 2xGBE






































































































































Reviews:

No comments

Related manuals for SCE 1000 2xGBE

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

Brand: Omnia Pages: 102

Brand: YASKAWA Pages: 34

Brand: IBA Pages: 29

Brand: Oracle Pages: 24

Brand: Opengear Pages: 2

Brand: Cypress Semiconductor Pages: 11

Surround Dongle

Brand: Sennheiser Pages: 18

Brand: NA Pages: 22

SLK-R602 Series

Brand: Seriallink Pages: 29

EK-Quantum Momentum ROG Rampage VI Encore

Brand: EK Pages: 11

Brand: Lanner Pages: 38

Brand: Allied Telesis Pages: 34

Brand: MFJ Pages: 11

Brand: NBase Pages: 18

Brand: Gearlinx Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands