Cisco LRE CPE Hardware Installation Manual Download Page 45 | Manualshive

Page: 45 / 106

background image

2-7

Cisco LRE CPE Hardware Installation Guide

78-11469-04

Chapter 2 Installation

Preparing for Installation

Cisco 576 LRE 997 Ethernet Connection Warning for Norway and Sweden

To reduce the risk of electric shock in Norwegian and Swedish LRE installations
with a Cisco 576 LRE 997 CPE device, do not connect the Ethernet port of the
Cisco 576 LRE 997 CPE to ports of other equipment as described in this warning:

Warning

To reduce the risk of electrical shock, do not connect the Ethernet port of the
Cisco 576 Long-Reach Ethernet (LRE) 997 customer premises equipment (CPE)
device to ports of other equipment if those ports have protective earth
conductors.

Advarsel

For å redusere risikoen for elektrisk støt, skal Ethernet-porten på Cisco 576
Long-Reach Ethernet (LRE)-kundeutstyr 997 (CPE) ikke tilkoples porter på
annet utstyr, hvis disse portene er utstyrt med vernejordingsledere.

Varning!

För att minska risken för elektrisk stöt, får inte Ethernet-porten på
Cisco 576 LRE (Long-Reach Ethernet) 997 CPE-enheter (customer premises
equipment) anslutas till portar på annan utrustning om dessa portar är
försedda med skyddsjordledare.

«
...
43
44
45
46
47
...
»

Summary of Contents for LRE CPE











































































































Reviews:

No comments

Related manuals for LRE CPE

Brand: ABLE Pages: 5

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

DKVM-16 - KVM Switch

Brand: D-Link Pages: 24

Dis-200G Series

Brand: D-Link Pages: 161

Dis-200G Series

Brand: D-Link Pages: 16

Dis-200G Series

Brand: D-Link Pages: 47

Brand: D-Link Pages: 25

DGS-3100 SERIES

Brand: D-Link Pages: 54

DGS-3100 SERIES

Brand: D-Link Pages: 220

Brand: D-Link Pages: 24

DGS-1248T - Switch

Brand: D-Link Pages: 52

DGS-1216T - Switch

Brand: D-Link Pages: 42

DGS-1216T - Switch

Brand: D-Link Pages: 10

Brand: D-Link Pages: 8

Brand: D-Link Pages: 379

Brand: D-Link Pages: 240

Brand: D-Link Pages: 188

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands