Cisco Catalyst 2928 Software Configuration Manual Download Page 96 | Manualshive

Page: 96 / 700

background image

5-4

Catalyst 2928 Switch Software Configuration Guide

OL-23389-01

Chapter 5 Clustering Switches

Planning a Switch Cluster

Planning a Switch Cluster

Anticipating conflicts and compatibility issues is a high priority when you manage several switches
through a cluster. This section describes these guidelines, requirements, and caveats that you should
understand before you create the cluster:

•

Automatic Discovery of Cluster Candidates and Members, page 5-4

•

HSRP and Standby Cluster Command Switches, page 5-9

•

IP Addresses, page 5-12

•

Hostnames, page 5-12

•

Passwords, page 5-12

•

SNMP Community Strings, page 5-13

•

and RADIUS, page 5-13

•

LRE Profiles, page 5-13

Refer to the release notes for the list of Catalyst switches eligible for switch clustering, including which
ones can be cluster command switches and which ones can only be cluster member switches, and for the
required software versions and browser and Java plug-in configurations.

Automatic Discovery of Cluster Candidates and Members

The cluster command switch uses Cisco Discovery Protocol (CDP) to discover cluster member switches,
candidate switches, neighboring switch clusters, and edge devices across multiple VLANs and in star or
cascaded topologies.

Note

Do not disable CDP on the cluster command switch, on cluster members, or on any cluster-capable
switches that you might want a cluster command switch to discover. For more information about CDP,
see

Chapter 23, “Configuring CDP.”

Following these connectivity guidelines ensures automatic discovery of the switch cluster, cluster
candidates, connected switch clusters, and neighboring edge devices:

•

Discovery Through CDP Hops, page 5-4

•

Discovery Through Non-CDP-Capable and Noncluster-Capable Devices, page 5-5

•

Discovery Through Different VLANs, page 5-6

•

Discovery Through Different Management VLANs, page 5-7

•

Discovery of Newly Installed Switches, page 5-8

Discovery Through CDP Hops

By using CDP, a cluster command switch can discover switches up to seven CDP hops away (the default
is three hops) from the edge of the cluster. The edge of the cluster is where the last cluster member
switches are connected to the cluster and to candidate switches. For example, cluster member switches 9
and 10 in

are at the edge of the cluster.

«
...
94
95
96
97
98
...
»

Summary of Contents for Catalyst 2928





























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 2928

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

ControlPoint 2000

Brand: 4Home Pages: 20

Brand: M86 Security Pages: 309

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: KYLAND Technology Pages: 24

Brand: AIC Pages: 101

ADSL Ethernet & USB Combo Router Lynx L-510

Brand: Starbridge Networks Pages: 59

Brand: M-system Pages: 4

Brand: Kramer Pages: 56

Brand: Kasda Pages: 39

Brand: LevelOne Pages: 83

Brand: Manson Engineering Industrial Pages: 10

Brand: NetComm Pages: 75

Brand: Proscend Pages: 93

Cheetah EtherCard-2320

Brand: Accton Technology Pages: 10

Brand: C&H Technologies Pages: 2

Brand: Proxim Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands