Cisco Catalyst 2928 Software Configuration Manual Download Page 278 | Manualshive

Page: 278 / 700

background image

13-10

Catalyst 2928 Switch Software Configuration Guide

OL-23389-01

Chapter 13 Configuring VLANs

Configuring Extended-Range VLANs

Switch(config-if)#

switchport mode access

Switch(config-if)#

switchport access vlan 2

Switch(config-if)#

end

Configuring Extended-Range VLANs

When the switch is in VTP transparent mode (VTP disabled), you can create extended-range VLANs (in
the range 1006 to 4094). Extended-range VLANs enable service providers to extend their infrastructure
to a greater number of customers. The extended-range VLAN IDs are allowed for any switchport
commands that allow VLAN IDs.

Extended-range VLAN configurations are not stored in the VLAN database, but because VTP mode is
transparent, they are stored in the switch running configuration file, and you can save the configuration
in the startup configuration file by using the

copy running-config startup-config

privileged EXEC

command.

Note

Although the switch supports 4094 VLAN IDs, see the

“Supported VLANs” section on page 13-2

the actual number of VLANs supported.

These sections contain extended-range VLAN configuration information:

•

Default VLAN Configuration, page 13-10

•

Extended-Range VLAN Configuration Guidelines, page 13-10

•

Creating an Extended-Range VLAN, page 13-11

Default VLAN Configuration

Table 13-2 on page 13-7

for the default configuration for Ethernet VLANs. You can change only the

MTU size and the remote SPAN configuration state on extended-range VLANs; all other characteristics
must remain at the default state.

Extended-Range VLAN Configuration Guidelines

Follow these guidelines when creating extended-range VLANs:

•

VLAN IDs in the extended range are not saved in the VLAN database and are not recognized by
VTP.

•

You cannot include extended-range VLANs in the pruning eligible range.

•

The switch must be in VTP transparent mode when you create extended-range VLANs. If VTP mode
is server or client, an error message is generated, and the extended-range VLAN is rejected.

•

You can set the VTP mode to transparent in global configuration mode or in VLAN database
configuration mode. See the

“Disabling VTP (VTP Transparent Mode)” section on page 14-10

should save this configuration to the startup configuration so that the switch boots up in VTP
transparent mode. Otherwise, you lose the extended-range VLAN configuration if the switch resets.

•

STP is enabled by default on extended-range VLANs, but you can disable it by using the

no

spanning-tree vlan

vlan-id

global configuration command. When the maximum number of

spanning-tree instances are on the switch, spanning tree is disabled on any newly created VLANs.

«
...
276
277
278
279
280
...
»

Summary of Contents for Catalyst 2928





























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 2928

Brand: D-Link Pages: 14

Brand: D-Link Pages: 7

Brand: D-Link Pages: 41

Brand: 3xLogic Pages: 2

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: DCE Pages: 5

RouterBOARD Groove

Brand: MikroTik Pages: 4

Brand: Edgewater Networks Pages: 7

Brand: NETGEAR Pages: 2

Brand: Perle Pages: 2

JetFusion 2100 Series

Brand: Paradyne Pages: 296

Brand: Ubiquiti Pages: 28

Brand: Sierra Wireless Pages: 2

B-Control Fader BCF2000

Brand: Behringer Pages: 13

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

ExtremeCloud Appliance E1120

Brand: Extreme Networks Pages: 219

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands