CipherLab 9500CE Series Reference Manual Download Page 113

Page: 113 / 131

Chapter 5 Applications

103

2D tab

UPC / EAN

Supported on 2D Reader

Default

Enable UPC-A

YES or NO

YES (Enabled)

Enable UPC-E0

YES or NO

YES (Enabled)

Enable UPC-E1

YES or NO

NO (Disabled)

Enable EAN-8

YES or NO

YES (Enabled)

Enable EAN-13

YES or NO

YES (Enabled)

Enable Bookland
EAN

YES or NO

*EAN-13 must be enabled!

NO (Disabled)

Decode
Supplementary

Digits (Addon 2 & 5)

When enabled, Addon 2 and Addon 5 of UPC /EAN
families can be decoded too.

Ignore Supplementals

Only with Supplementals (Decode barcodes with
Addons only.)

Enable Supplementals (Decode barcodes with or
without Addons.)

Ignore
Supplementals
(Disabled)

Supplementary

Redundancy

With “Enable Supplementals” is selected, it will
autodiscriminate barcodes with or without
supplementals.

Select a desired level of reading (decoding) security.
Comprise some speed for getting more security when
necessary. By default, it requires ten more successful
decoding to make the reading of supplementals
(Addons) valid.

1~255 (decode times)

10 times

Transmit UPC-A

Check Digit

YES or NO

YES (Enabled)

Transmit UPC-E0
Check Digit

YES or NO

YES (Enabled)

Transmit UPC-E1

Check Digit

YES or NO

YES (Enabled)

UPC-A Preamble

By default, the selected UPC-A preamble is included in
the data being transmitted.

No Preamble

System Character

System Character & Country Code

System
Character

UPC-E0 Preamble

By default, the selected UPC-E0 preamble is included
in the data being transmitted.

System
Character

UPC-E1 Preamble

By default, the selected UPC-E1 preamble is included
in the data being transmitted.

System
Character

Summary of Contents for 9500CE Series




































































































































Search results

Summary of Contents for 9500CE Series

Reviews:

Related manuals for 9500CE Series

Brands by name

Popular brands

CipherLab 9500CE Series, Reference Manual

Search results

Summary of Contents for 9500CE Series

Reviews:

Related manuals for 9500CE Series

Brands by name

Popular brands