manualshive.com logo in svg

Chrysler Stratus LHD 1997, Interactive Electronic Service Manual

The Chrysler Stratus LHD 1997 Interactive Electronic Service Manual is a comprehensive resource for owners and enthusiasts. This user-friendly manual allows you to easily navigate through detailed instructions, diagrams, and troubleshooting tips. Download this valuable manual for free from our website and maximize your vehicle's performance and maintenance.

Share
Download
background image

cause of low compression unless some malfunc-
tion is present.

(11)

Clean or replace spark plugs as necessary

and adjust gap as specified in Group 8, Electrical.
Tighten to specifications.

(12)

Test resistance of spark plug cables. Refer to

Group 8, Electrical Ignition System Secondary Cir-
cuit Inspection.

(13)

Test coil output voltage, primary and second-

ary resistance. Replace parts as necessary. Refer to
Group 8, Electrical Ignition System.

(14) Check fuel pump pressure at idle and differ-

ent RPM ranges. Refer to Group 14, Fuel System for
Specifications.

(15)

The air filter elements should be replaced as

specified in Group 0, Lubrication and Maintenance,.

(16)

Inspect crankcase ventilation system as out

lined in Group 0, Lubrication and Maintenance. For
emission controls see Group 25, Emission Controls
for service procedures.

(17) Inspect and adjust accessory belt drives refer-

ring to Group 7, Cooling System, Accessory Drive
Belts for proper adjustments.

(18)

Road test vehicle as a final test.

CYLINDER COMBUSTION PRESSURE LEAKAGE
TEST

The combustion pressure leakage test provides an

accurate means for determining engine condition.

Combustion pressure leakage testing will detect:

•

Exhaust and intake valve leaks (improper seat-

ing).

•

Leaks between adjacent cylinders or into water

jacket.

•

Any causes for combustion/compression pressure

loss.

WARNING:

DO NOT REMOVE THE RADIATOR CAP

WITH THE SYSTEM HOT AND UNDER PRESSURE
BECAUSE SERIOUS BURNS FROM COOLANT CAN
OCCUR.

Check the coolant level and fill as required. DO

NOT install the radiator cap.

Start and operate the engine until it attains nor-

mal operating temperature, then turn the engine
OFF.

Clean spark plug recesses with compressed air.
Remove the spark plugs.
Remove the oil filler cap.
Remove the air cleaner.
Calibrate the tester according to the manufactur-

er’s instructions. The shop air source for testing
should maintain 483 kPa (70 psi) minimum, 1 379
kPa (200 psi) maximum and 552 kPa (80 psi) recom-
mended.

Perform the test procedures on each cylinder

according to the tester manufacturer’s instructions.
While testing, listen for pressurized air escaping
through the throttle body, tailpipe and oil filler cap
opening. Check for bubbles in the radiator coolant.

All gauge pressure indications should be equal,

with no more than 25% leakage.

FOR EXAMPLE: At 552 kPa (80 psi) input pres-

sure, a minimum of 414 kPa (60 psi) should be main-
tained in the cylinder.

LASH ADJUSTER (TAPPET) NOISE DIAGNOSIS

A tappet-like noise may be produced from several

items. Check the following items.

(1) Engine oil level too high or too low. This may

cause aerated oil to enter the adjusters and cause
them to be spongy.

(2) Insufficient running time after rebuilding cylin-

der head. Low speed running up to 1 hour may be
required.

(3) During this time, turn engine off and let set for

a few minutes before restarting. Repeat this several
times after engine has reached normal operating
temperature.

(4) Low oil pressure.
(5) The oil restrictor pressed into the vertical oil

passage to the cylinder head is plugged with debris.

(6) Air ingested into oil due to broken or cracked

oil pump pick up.

(7) Worn valve guides.
(8) Rocker

arm

ears

contacting

valve

spring

retainer.

(9) Rocker arm loose, adjuster stuck or at maxi-

mum extension and still leaves lash in the system.

(10) Faulty lash adjuster.
a. Check

lash

adjusters

for

sponginess

while

installed in cylinder head. Depress part of rocker
arm over adjuster. Normal adjusters should feel very
firm. Spongy adjusters can be bottomed out easily.

b. Remove suspected lash adjusters, and disassem-

ble Do not reuse retainer caps . Do not inter-
change

parts

and

make

sure

that

care

and

cleanliness is exercised in the handling of parts.

c. Clean out dirt and varnish with solvent.
d. Reassemble with engine oil.
e. Check for sponginess.
f. If still spongy, replace with new adjuster.

INSPECTION (ENGINE OIL LEAKS IN GENERAL)

Begin with a through visual inspection of the

engine, particularly at the area of the suspected leak.
If an oil leak source is not readily identifiable, the
following steps should be followed:

(1) Do not clean or degrease the engine at this

time because some solvents may cause rubber to
swell, temporarily stopping the leak.

9 - 8

ENGINE

JA

DIAGNOSIS AND TESTING (Continued)

Summary of Contents for Stratus LHD 1997































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratus LHD 1997

Garmin BC 30 Owner'S Manual preview
BC 30
Brand: Garmin Pages: 2
EUFAB 12015 Manual preview
12015
Brand: EUFAB Pages: 12
Velleman CAMCOLC1N User Manual preview
CAMCOLC1N
Brand: Velleman Pages: 6
RBP STEALTH POWER RBP-216-SP Installation Manual preview
STEALTH POWER RBP-216-SP
Brand: RBP Pages: 16
HURST STREET SUPER SHIFTER Installation Instructions preview
STREET SUPER SHIFTER
Brand: HURST Pages: 2
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Brand: Menabo Pages: 8
Jaeger J05252127 Fitting Instructions Manual preview
J05252127
Brand: Jaeger Pages: 17
Improved Racing E5G-601 Instructions Manual preview
E5G-601
Brand: Improved Racing Pages: 17
ULTIMATE SPEED 279619 Instructions For Use And Safety Manuallines preview
279619
Brand: ULTIMATE SPEED Pages: 40
Honda 2010 Accord Coupe Owner'S Manual preview
2010 Accord Coupe
Brand: Honda Pages: 410
Honda Civic Hatch 2017 Owner'S Manual preview
Civic Hatch 2017
Brand: Honda Pages: 687
Rugged Ridge 13551.33 Manual preview
13551.33
Brand: Rugged Ridge Pages: 3
Phonocar 6/946 Instruction Manual preview
6/946
Brand: Phonocar Pages: 4
Dodge 2005 Sprinter User Manual preview
2005 Sprinter
Brand: Dodge Pages: 60
Vauxhall Signum Owner'S Manual preview
Signum
Brand: Vauxhall Pages: 310
Whispbar K536W Fitting Instructions Manual preview
K536W
Brand: Whispbar Pages: 17
Brodit 841488 Quick Start Manual preview
841488
Brand: Brodit Pages: 2
Scion 2015 FR-S Quick Reference Manual preview
2015 FR-S
Brand: Scion Pages: 24

Brands by name

Popular brands

Load more brands