Chrysler Crossfire 2007 Owner'S Manual Download | Manualshive

Page: 49 / 299

background image

Here are some tips on getting the most out of your child
restraint:

•

Before buying any restraint system, make sure that it
has a label certifying that it meets all applicable Safety
Standards. We also recommend that you make sure
that you can install the child restraint in the vehicle
where you will use it before you buy it.

•

The restraint must be appropriate for your child’s
weight and height. Check the label on the restraint for
weight and height limits.

•

Carefully follow the instructions that come with the
restraint. If you install the restraint improperly, it may
not work when you need it.

•

Buckle the child into the seat according to the seat
manufacturer’s directions.

•

When your child restraint is not in use, secure it in the
vehicle with the seat belt or remove it from the vehicle.
Do not leave it loose in the vehicle. In a sudden stop or
collision, it could strike the occupants and cause
serious personal injury.

NOTE:

For

additional

information

refer

to

www.seatcheck.org or call 1–866–SEATCHECK.

Older Children and Child Restraints
Children who weigh more than 20 lbs. (9 kg) and who are
older than one year can ride forward-facing in the
vehicle. Forward-facing child seats and convertible child
seats used in the forward-facing direction are for children
who weigh 20 to 40 lbs. (9 to 18 kg) and who are older
than one year. These child seats are also held in the
vehicle by the lap/shoulder belt or the LATCH child
restraint anchorage system. (See LATCH - Child Seat
Anchorage System section.)

The belt-positioning booster seat is for children weighing
more than 40 lbs. (18 kg), but who are still too small to fit
the vehicle’s seat belts properly. If the child cannot sit
with knees bent over the vehicle’s seat cushion while the
child’s back is against the seat back, they should use a
belt-positioning booster seat. The child and belt-
positioning booster seat are held in the vehicle by the
lap/shoulder belt.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

49

2

«
...
47
48
49
50
51
...
»

Summary of Contents for Crossfire 2007












































































































































































































































































































Reviews:

No comments

Related manuals for Crossfire 2007

Brand: Hama Pages: 2

Brand: Abarth Pages: 36

Brand: Warrior Products Pages: 3

Brand: Horn Tools Pages: 6

Quattroporte Automatic

Brand: Maserati Pages: 272

Xplore Pro II SxS

Brand: Marlon Pages: 15

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

Brand: Ranger design Pages: 22

Quantum hardcoated N30216

Brand: National Cycle Pages: 3

Brand: Yakima Pages: 12

Brand: FALCON RIDGE Pages: 6

Brand: Flash Cover Pages: 2

Brand: Porsche Pages: 98

Brand: Improved Racing Pages: 17

Brand: Power Acoustik Pages: 4

Speed & Route Profiler

Brand: Racelogic Pages: 24

Brand: r.LiNK Pages: 21

Brand: Toyota Pages: 672

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands