Chrysler Crossfire 2007 Owner'S Manual Download | Manualshive

Page: 108 / 299

background image

If the indicator light blinks rapidly for two seconds
and then turns to a constant light, continue with
Programming Steps 8-10 to complete programming of
a rolling code equipped device (most commonly a
garage door opener).

8. At the garage door opener receiver (motor-head unit)
in the garage, locate the “learn” or “smart” button. This
can usually be found where the hanging antenna wire is
attached to the motor-head unit.

9. Firmly press and release the “learn” or “smart” but-
ton. (The name and color of the button may vary by
manufacturer.)

NOTE:

There are 30 seconds in which to initiate Step 10.

10. Return to the vehicle and firmly press, hold for two
seconds and release the programmed universal trans-
ceiver button. Repeat the “press/hold/release” sequence
a second time, and, depending on the brand of the garage
door opener (or other rolling code equipped device),
repeat this sequence a third time to complete the pro-
gramming.

The universal transceiver should now activate your roll-
ing code equipped device.

If you do not successfully program the universal trans-
ceiver to learn the signal of your hand-held transmitter,
call toll free for customer assistance at 1-800-355-3515, or
on the internet at www.homelink.com.

Gate Operator/Canadian Programming

Canadian radio-frequency laws require transmitter sig-
nals to “time-out” (or quit) after several seconds of
transmission. This may not be long enough for the
universal transceiver to pick up the signal during pro-
gramming. Similar to this Canadian law, some U.S. gate
operators are designed to “time-out” in the same manner.

If you live in Canada or you are having difficulties
programming a gate operator by using the programming
procedures (regardless of where you live), replace Pro-
gramming Step 5 with the following:

NOTE:

If programming a garage door opener or gate

operator, it is advised to unplug the device during the
“cycling” process to prevent possible overheating.

108

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
106
107
108
109
110
...
»

Summary of Contents for Crossfire 2007












































































































































































































































































































Reviews:

No comments

Related manuals for Crossfire 2007

Brand: Valeo Pages: 17

Brand: VEAP SHIELD UNITED Pages: 3

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: Pacbrake Pages: 14

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: Brodit Pages: 2

Brand: Power Fist Pages: 12

Brand: EAL Pages: 7

Brand: P-Invent Pages: 4

Brand: Boyo Pages: 9

Brand: Speedtech Pages: 12

Brand: Altius Pages: 16

Sportsman 40-0125

Brand: Westin Pages: 2

1997 Park Avenue

Brand: Buick Pages: 420

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands