Christini AWD 250 Service Manual Download Page 88

Page: 88 / 124

Page 87

•

Remove the forks and spline bearing assembly.

•

Remove the 4 cover bolts from the bottom of the triple clamp with
a 6mm Allen wrench.

•

Carefully pull on the shaft sprockets and ease the cover down from

the bottom triple clamp. The Left shaft will pull down with the
cover. The right shaft will stay in place and the cover will slide
down over it.

Note:

Note: To service the triple clamp chains, sprockets and bearings it is recommended that you leave the bottom triple
clamp attached to the bike. This will make it easier to pull the cover off. For servicing the steerer tube bearings, or

replacing the head tube gears, the triple clamps will need to be removed. For picture clarity, the triple clamp was re-
moved from the bike.

Triple Clamp Service

Summary of Contents for AWD 250





























































































































Search results

Summary of Contents for AWD 250

Reviews:

Related manuals for AWD 250

Brands by name

Popular brands

Christini AWD 250, Service Manual

Search results

Summary of Contents for AWD 250

Reviews:

Related manuals for AWD 250

Brands by name

Popular brands