Christini AWD 250 Service Manual Download Page 72

Page: 72 / 124

Page 71

•

Remove cover bearing with bearing removal punch. Note o-ring lip

near inner race of bearing is easily damaged. Only apply pressure
to inner race of bearing.

•

Remove drive insert from gear with hammer and bearing removal

tool.

•

Before reassembly of dropouts, all parts must be cleaned and

inspected individually for damage or wear. Parts can be cleaned
with solution no different then OEM fork. Be sure to blow dry
dropouts and parts prior to reassembly if cleaning solution is used.

•

Pinion and bevel gear must be replaced as a set.

•

If bearings are seized or hard to turn by hand they must be
replaced or cleaned and repacked with grease.

•

Be sure to grease all o-rings and gears during reassembly.

Dropout Service

Summary of Contents for AWD 250





























































































































Search results

Summary of Contents for AWD 250

Reviews:

Related manuals for AWD 250

Brands by name

Popular brands

Christini AWD 250, Service Manual

Search results

Summary of Contents for AWD 250

Reviews:

Related manuals for AWD 250

Brands by name

Popular brands