Christini AWD 250 Service Manual Download Page 74 | Manualshive

Page: 74 / 124

background image

Page 73

Note:

Note:

Note:

Note: Be sure dropout is clean before proceeding

•

Insert top pinion bearings and seal into driveshaft bore at top of
dropout using bearing driver. Note, be careful not to damage seal
or nick chrome fork plating with hammer. Use plastic faced
hammer.

•

Apply light grease to pinion seal

•

Insert bottom pinion bearing onto pinion gear.

WARNING:

WARNING:

WARNING:

WARNING: black seal must be facing down towards gear teeth. If
bearing is not inserted correctly, severe damage can occur!

•

Slide bearing and pinion gear into bore. Make sure bearing is fully
seated.

Dropout Service

Warning:

Warning:

Warning:

Warning: Bevel gears are right and left hand specific and must be installed in the correct dropout or damage to the
system can occur. The Left Bevel Gear Set shown below must go in the disk side dropout. Note the difference in the
spiral direction on each gear set.

«
...
72
73
74
75
76
...
»

Summary of Contents for AWD 250





























































































































Reviews:

No comments

Related manuals for AWD 250

Brand: Can-Am Pages: 16

Brand: Can-Am Pages: 254

Brand: X-lite Pages: 6

Brand: Yamaha Pages: 860

990D0-44G00-ALM

Brand: Suzuki Pages: 24

DaVinci RSV4-APRC

Brand: STARLANE Pages: 2

Brand: IRC Pages: 2

Brand: hepco & becker Pages: 7

Brand: SHERCO Pages: 102

Brand: paladin Pages: 2

Brand: Yamaha Pages: 248

Brand: Yamaha Pages: 86

Brand: dushi Pages: 4

Brand: Honda Pages: 180

Brand: Hudora Pages: 8

Sport 1 180 - 487.3

Brand: CZ Pages: 42

Brand: Kuberg Pages: 38

Brand: Wunderlich Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands