Christie J 2.0kW Service Manual Download Page 41

Page: 41 / 94

Section 4: Parts and Module Replacement

J Series 2.0, 2.4, and 3.0kW Service Manual

4-21

020-100739-01 Rev. 1 (01-2012)

1. Turn the lamp and projector off. Allow the projector to cool for a minimum of 5 minutes.
2. Unplug the projector.
3. Put on your protective clothing and face shield.
4. Loosen the captive screws securing the lamp door.

5. Loosen the screw holding the lamp module handle.

6. Pull the lamp module handle outward to remove the lamp. Place the lamp in a protective case and follow

the disposal procedure for your location.

Roadster S+22K-J

132-016119-xx

3.0 kW

003-000306-xx

Mirage S+22K-J

132-016120-xx

Roadster HD20K-J

132-017110-xx

Mirage HD20K-J

132-017121-xx

Roadster WU20K-J

132-018111-xx

Mirage WU20K-J

132-018122-xx

Matrix WU20K-J

132-018133-xx

Table 4.2

Summary of Contents for J 2.0kW































































































Search results

Summary of Contents for J 2.0kW

Reviews:

Related manuals for J 2.0kW

Brands by name

Popular brands

Christie J 2.0kW, Service Manual

Search results

Summary of Contents for J 2.0kW

Reviews:

Related manuals for J 2.0kW

Brands by name

Popular brands