Christie J 2.0kW Service Manual Download Page 37

Page: 37 / 94

Section 4: Parts and Module Replacement

J Series 2.0, 2.4, and 3.0kW Service Manual

4-17

020-100739-01 Rev. 1 (01-2012)

a. Disconnect the 3 AC line filter connectors.

9. Remove the AC line filter.
10. Install the new AC line filter.

4.5.11 Remove and Replace the AC Power Switch (2.0kW & 2.4kW)

1. Power down the projector:

a. Turn the projector off and allow the projector to cool for a minimum of 5 minutes.
b. Disconnect the AC power cord from the rear of the projector.

2. Remove the rear cover:

a. Loosen the 8 quick-release screws on the rear cover.
b. Move the cover away from the rear of the projector to access the keypad PCB.
c. Disconnect the projector keypad harness connector P65.
d. Remove the rear cover and set it aside.

3. Remove the power cord retaining clip and the 8 screws from the AC cover panel.

4. Pull the left side of the AC cover panel towards you while you slide the right side and pull it forward to

access the AC power switch.

Summary of Contents for J 2.0kW































































































Search results

Summary of Contents for J 2.0kW

Reviews:

Related manuals for J 2.0kW

Brands by name

Popular brands

Christie J 2.0kW, Service Manual

Search results

Summary of Contents for J 2.0kW

Reviews:

Related manuals for J 2.0kW

Brands by name

Popular brands