Christie J 2.0kW Service Manual Download Page 28 | Manualshive

Page: 28 / 94

background image

4-8

J Series 2.0, 2.4, and 3.0kW Service Manual

020-100739-01 Rev. 1 (01-2012)

Section 4: Parts and Module Replacement

9. Install the new LCM.

a. Lubricate the radiator hose connector o-ring with a small amount of coolant.
b. Install the hose connector straight onto the mating connector. Do not tilt the connector or it will

damage the o-ring.

c. Turn clockwise.
d. Power up the projector and inspect for leaks.

4.5.2

Remove and Replace AC Lamp Blower Fan

1. Power down the projector:

a. Turn the projector off and allow the projector to cool for a minimum of 5 minutes.
b. Disconnect the AC power cord from the rear of the projector.

2. If installed, remove the 3 stacking mounts from the top cover:

a. Remove and set aside the safety pin.
b. Remove the screw.
c. Remove the mount, the screw, and the spring and set them aside.
d. Repeat steps a to c for the remaining mounts.

3. Remove the 8 screws holding the top cover and then remove the top cover and set it aside.
4. Remove the non-lens side cover:

a. Loosen the 6 quick-release screws for the side cover.
b. Remove the cover and set it aside.

5. Remove the lamp ballast.
6. Remove the 8 AC terminal bracket screws.
7. Disconnect ballast harness from line filter & ground for 2.4 & 3.0kW and move it aside to access the lamp

blower screws.

«
...
26
27
28
29
30
...
»

Summary of Contents for J 2.0kW































































































Reviews:

No comments

Related manuals for J 2.0kW

Brand: Patton electronics Pages: 3

ADVANTAGE ELECTROL

Brand: Da-Lite Pages: 2

50ML8205D - 50" Hd Dlp™ Projection Tv

Brand: Magnavox Pages: 40

Brand: Acer Pages: 62

Brand: Acer Pages: 58

S1370WHn Series

Brand: Acer Pages: 64

Brand: Acer Pages: 140

Brand: Acer Pages: 126

Brand: Acer Pages: 2

Brand: NEC Pages: 2

Brand: Optoma Pages: 93

Brand: DNP Pages: 2

Home Entertainment W100

Brand: BenQ Pages: 47

Brand: Projectiondesign Pages: 33

Brand: Eiki Pages: 66

Brand: Panasonic Pages: 167

Brand: Barco Pages: 22

Brand: Hitachi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands