manualshive.com logo in svg

Chevrolet 2001 Monte Carlo, Owner'S Manual

Share
Download
Chevrolet 2001 Monte Carlo Owner'S Manual Download Page 274

5-21

9. Put the cap back on the coolant recovery tank, but

leave the radiator pressure cap off.

10. Start the engine and let it run until you can feel the

upper radiator hose getting hot. Watch out for the
engine cooling fans.

11. By this time, the coolant level inside the radiator

filler neck may be lower. If the level is lower, add
more of the proper DEX

-

COOL

R

 coolant mixture

through the filler neck until the level reaches the
base of the filler neck.

12. Then replace the pressure cap. At any time during

this procedure if coolant begins to flow out of the
filler neck, reinstall the pressure cap. Be sure the
arrows on the pressure cap line up like this.

13. Check the coolant in the recovery tank. The level in

the coolant recovery tank should be at the HOT
mark when the engine is hot or at the COLD mark
when the engine is cold.

Summary of Contents for 2001 Monte Carlo










































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands