manualshive.com logo in svg

CHEELCARE Companion, User Manual

Share
Download
CHEELCARE Companion User Manual Download Page 29

 

V1.1, May 12, 2020 

Companion User Manual 

 

©Copyright 2020 by CHEELCARE

TM

. All rights reserved. 

P a g e

 | 

26

 

 

Companion Maintenance 

The Companion has been carefully designed for optimal performance. To ensure its long-lasting 
service and to prolong its lifespan, the following maintenance tasks and general precautions 
must be followed. It is strongly recommended to perform periodic maintenance and safety 
checks on the Companion by following these steps, as improper maintenance may cause failure 
and invalidate the warranty.  

Battery and Charging 

1.  Do not let the battery discharge completely. When the system indicates a low battery 

charge, charge the battery as soon as possible.  

2.  Only use the charger provided with the Companion. 
3.  Do not insert any metal or other objects into the charging port of the Companion, as this 

may cause unit damage and/or personal injury.  

4.  When not in use, the Companion should be kept in a dry environment at a room 

temperature in a range of 10°C to 25°C (50°F - 77°F). Using or storing the Companion 
beyond recommended temperature range may shorten the battery life. 

5. 

If your Companion is not going to be used for a long period of time, make sure it is still 

being fully charged every two months in order to avoid “deep discharge” battery damage.

 

Cleaning and Overall Care 

1. 

  Always ensure the Companion is powered off and the charger is unplugged before 

cleaning to prevent damage and the risk of electric shock. 

2.  The exterior frame and wheel can be cleaned using a soft cloth dipped in non-abrasive 

soap and water.  

3. 

  Do not use high pressure washers like a hose or water gun. Never submerge the 

entire Companion under water. 

4.  Store the device indoors in dry conditions. Keeping the Companion in an outdoor 

environment with strong sunlight may cause the finish to fade more quickly or cause 
other deterioration. 

5.  It is recommended to regularly perform small maintenance tasks such as tightening 

screws and aligning handlebars to keep your Companion safe and in top shape. Please 
contact CHEELCARE for any significant maintenance issues or for any problems you 
are unable to solve. 

6. 

  

Do not disassemble the Companion’s Power Unit. The devic

e's internal structure is 

very precise and can be easily damaged unless handled by authorized service 
professionals. The manufacturer can not hold be responsible for any personal injury or 
property damage caused by total or partial disassembly of the Compa

nion’s Power Unit.

 

 

 

Summary of Contents for Companion


































Reviews:

No comments

Brands by name

Popular brands

Load more brands