manualshive.com logo in svg

CHEELCARE Companion, User Manual

Share
Download
CHEELCARE Companion User Manual Download Page 13

 

V1.1, May 12, 2020 

Companion User Manual 

 

©Copyright 2020 by CHEELCARE

TM

. All rights reserved. 

P a g e

 | 

10

 

 

Assembling the Docking Module for Rigid Manual Wheelchair

 

instructions

 (

page 12).

 

Assembling the Docking Module for Foldable Wheelchairs 

1.  Slightly fold your wheelchair to easily access the frame tubes. Locate the package with 

the set of clamps, rubber rings and strips. Check that your chair can accommodate 
clamps in orientation #1 otherwise, use orientation #2. Position both halves of the clamps 
on the side of the frame tubes upon the chosen orientation. If the clamps do not fit tightly 
around the frame tubes, choose appropriate rubber rings or strips, and attach them 
between the clamp and tube to ensure a tight fit. Secure the clamps in place with the 
screws by using an Allen key, but do not tighten them yet. 

 

 

 

Clamp orientation #1 

Clamp orientation #2 

Mounting frame 

tubes 

Clamp screws 

Summary of Contents for Companion


































Reviews:

No comments

Brands by name

Popular brands

Load more brands