background image

19 

 

 

Warranty C ard

 

(Please fill out completely & return with a copy of the receipt)

  

 

Owner’s Name: _______________________________________________________ 

Owner’s Signature:_____________________________________________________  

Address:   ___________________________________Ph #: ___________________ 

City:  _______________________________  State: _______    Zip: ______________  

Date of Purchase:  ________________ 

Business Where Trap Was purchased:____________________________________ 

 

WARRANTY CERTIFICATE 

 

Your new

 WHEELYBIRD

TM

 AUTO-FEED TRAP

 is warranted to be free from defects in material or 

workmanship for a period of six (6) months from the date of purchase.  This warranty is extended only 

to the original consumer purchaser.  Should you believe that your trap is defective in material or workmanship,

you should contact the 

CHAMPION 

Customer Service Department via phone at 800-379-1732. 

 

In the event a warranty repair is required, all parts will be provided at no charge. THIS WARRANTY DOES 

NOT COVER DEFECTS OR DAMAGE RESULTING FROM: CARELESSNESS, MISUSE, IMPROPER 

-

INSTALLATION, MODIFICATION, OR NORMAL WEAR AND TEAR.

 

IN ORDER FOR THIS WARRANTY TO BE IN EFFECT, 

YOU MUST FILL OUT THIS 

WARRANTY CARD  AND RETURN IT WITHIN 30 DAYS OF PURCHASE. 

THE ATTACHED 

WARRANTY CARD MUST BE FILLED OUT COMPLETELY AND SIGNED BY THE OWNER IN 

ORDER TO BE VALID. WARRANTY SERVICES CANNOT BE PROVIDED WITHOUT MEETING

 

THE ABOVE REQUIREMENT. Retain this warranty certificate for future reference. THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

 

LIMITED TO THE DURATION OF THIS LIMITED WARRANTY.

 

CHAMPION 

IS NOT LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE

OF THE PRODUCT AND UNDER NO CIRCUMSTANCES SHALL 

CHAMPION 

BE LIABLE

FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. HOWEVER, SOME STATES DO NOT 

ALLOW LIMITATIONS ON INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE ABOVE 

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

 

The above warranty provides the sole and exclusive warranty available to the customer in the 

event of a defect in material or workmanship in the 

CHAMPION WHEELYBIRD

TM

 AUTO-FEED 

TRAP. 

This warranty gives you specific legal rights, and you may also have other rights which vary 

from State to State. 

 

Summary of Contents for WHEELYBIRD 40909























Reviews: