Champion UH-100 Installation Manual Download Page 10

Page: 10 / 84

Unpack and Place

Placement of Dishwasher (continued)

2. Your dishwasher may be installed as a free-standing unit or under a counter-

top.

3. Typical counter-top height is 34". Refer to the illustration.

Countertop

Wall

3" Minimum Wall

Clearance

34"

Minimum

Height

Floor

Chemical Supply

Containers

Typical Undercounter Installation

Installation Guide

Unpack and Place

4. Counter installations must provide storage space for the dishwasher's

chemical supply containers. Container height must not exceed 10" above the

floor.

5. Chemical supply containers must be placed as close as possible to the side of

the dishwasher.

6. Check that the floor is level at the permanent location.

7. The dishwasher has adjustable feet for leveling.
8. Level the dishwasher front to back and side to side with a 24" bubble level to

match the permanent location.

9. Your dishwasher is ready for the utility connections.

Summary of Contents for UH-100





















































































Search results

Summary of Contents for UH-100

Reviews:

Related manuals for UH-100

Brands by name

Popular brands

Champion UH-100, Installation Manual

Search results

Summary of Contents for UH-100

Reviews:

Related manuals for UH-100

Brands by name

Popular brands