Champion UH-100 Installation Manual Download Page 20

Page: 20 / 84

Chemical Dispensers

1. All models come equipped with a built-

in detergent dispensing pump and a

rinse-aid dispensing pump. The pumps

are located behind the lower front

access panel.

2. Each pump is fitted with 6ft of pick-

up supply tubing, a stand-pipe, and a

strainer.

3. Pick-up tubes are marked detergent

and rinse-aid. Make sure the pick-

up tubes are placed in the correct

chemical supply container (chemicals

supplied by others).

4. The chemical dispensers require non-

chlorinated liquid detergent and rinse-

aid. Your chemical supplier must adjust

the dispensers for the supplied product.

5. Chemical containers must be placed

as close to the dishwasher as possible

and no higher than 10" above the floor.

Dispenser Pump Location

Pick-Up Tubes

Chemical Dispensers

Installation Guide

Chemical Dispensers

Summary of Contents for UH-100





















































































Search results

Summary of Contents for UH-100

Reviews:

Related manuals for UH-100

Brands by name

Popular brands

Champion UH-100, Installation Manual

Search results

Summary of Contents for UH-100

Reviews:

Related manuals for UH-100

Brands by name

Popular brands