Champion UH-100 Installation Manual Download Page 2

Page: 2 / 84

National Service Department

In Canada:

In the USA:

Toll-free: 800/ 263-5798

Toll-free: 800/ 532-8591

Tel:

905/ 562-4195

Tel:

336/ 661-1556

Fax:

905/ 562-4618

Fax:

336/ 661-1979

email: [email protected]

For all models:

The data plate is located on
the bottom left-hand side of
the dishwasher.

For future reference, record your dishwasher information in the box below.

Model Number__________________________ Serial Number_______________________

Voltage________________Hertz_____________ Phase__________________

Champion Service Agent __________________________________ Tel:______________________

Champion Parts Distributor _________________________________ Tel:______________________

ATTENTION:

The dishwasher model no., serial no.,

voltage, Hz and phase are needed to

identify your machine and to answer

questions.

Please have this information on-hand

if you call for service assistance.

We support

Summary of Contents for UH-100





















































































Search results

Summary of Contents for UH-100

Reviews:

Related manuals for UH-100

Brands by name

Popular brands

Champion UH-100, Installation Manual

Search results

Summary of Contents for UH-100

Reviews:

Related manuals for UH-100

Brands by name

Popular brands