Champion UH-100 Installation Manual Download Page 13

Page: 13 / 84

Electrical Connections

Installation Guide

Electrical Connections (continued)

(For Machines Beginning with S/N 14326 and Above)

To wash

tank heater

115VAC

From

main

terminal block

115 VAC

From

main

terminal block

1 PH

208-230VAC

No power

when booster

heater is

connected for

1 PH

No power when booster

heater is connected for 1 PH

To booster heater

1 PH 208-230VAC

1H2

1H3

1H1

Auxiliary

Contactor

Booster Heater

Contactor

To booster

heater contactor

1PH

208-230VAC

Auxiliary

Contactor

115VAC

No power when booster

heater is connected for 1 PH

No power when booster

heater is connected for 1 PH

Model UH100B, UH170B, and UH200B

Booster Heater/Wash Tank Heater Interlock Components

(Beginning with S/N 14326 and above)

Main Terminal Block (MTB)

1H1

1H2

1H3

Booster Heater

Connected for 1PH

1H1

Booster Heater

Connected for 3PH

1H2

1H3

Wire not

connected

Attention Authorized Service Technician

Booter heater and Wash tank heater Interlock Circuit

Models UH100B, UH170B, UH200B

See the illustration below. Models beginning with S/N 14326 and above have a

Booster Heater/

Wash Tank Heater Interlock

that removes power from the wash tank heater when the booster heater

contactor operates

(See the schematic on the back of the lower access panel).

1 Phase to 3 Phase Field Conversion

Models UH100B, UH170B, UH200B

Models beginning with S/N 14326 are wired for 1 PH operation. The Phase of the dishwasher may be

changed by changing the element jumpers for 3 Ph operation and connecting the wire marked 1H3 as

shown below. The 1H3 wire is located on the right-side of the booster heater wiring harness next to the

booster heater. To convert the booster heater:

1. Make sure power is turned off.

2. Remove the black booster heater cover.

3. Change the jumpers.

4. Replace the booster heater cover.

5. Request the a qualified electrician connect a 3 PH power supply to the machine.

Note:

1. The Main Terminal Block

(MTB) is a 4-pole connection

block.

2. The main incoming can be

1 PH or 3 PH depending on

the needs of the customer.

3. Instructions for the conversion

of the booster heater element

from 1 PH to 3 PH are located

on the back of the lower

access panel.

4. A new machine data plate is

located on the back of the

panel too.

THE OLD DATA PLATE ON

THE LOWER LEFT CONER

OF THE DISHWASHER

MUST BE REMOVED AND

REPLACED WITH THE NEW

DATA PLATE.

ONLY a qualified electrician

is allowed to change the

incoming power to the

machine.

Summary of Contents for UH-100





















































































Search results

Summary of Contents for UH-100

Reviews:

Related manuals for UH-100

Brands by name

Popular brands

Champion UH-100, Installation Manual

Search results

Summary of Contents for UH-100

Reviews:

Related manuals for UH-100

Brands by name

Popular brands