background image

SpaceKeeper Cons ole (SKC) – Ins tallation Operation Maintenance Manual

7

OPERATION

Cool Start Up

A call on “Y” for cooling initiates a s eries of checks prior to the s tart up of the

compres s or. These checks include:

a. Power ON timer – Compres s or operation is delayed for approximately 5

minutes after restoration of power. This prevents all units from coming

on-line at the s ame time when power is restored. It als o prevents

compres s or jolting in ins tances of intermittent power.

b. Anti-Recycle timer – There is a 5-minute anti-recycle delay timer that

allows the refrigeration cycle to achieve pres s ure equalization s o that

the compres s or is unloaded upon s tart up.

c. High Pres sure Switch – The high refrigerant pres s ure s witch must be

closed prior to s tart up. LED 11 will be ON. High pres s ure s witch opens at

600 ± 10 psi and clos es at 450 ± 10 ps i.

d. Low Pres s ure Switch – The low pres s ure s witch operates primarily as a

los s of charge protector. It must be clos ed for compres s or s tart up and

its LED 12 will be ON. Upon s tart up, the s ignal from the low pres s ure

s witch is ignored for 5 minutes. In s ome s ituations, particularly when

the unit is cold, the press ure switch will open during s tart-up. If the

s witch does not clos e within the 5 minute ignore period, the compres sor

will immediately be turned off. Low pres s ure s witch opens at 60 ± 3 psi

and clos es at 90 ± 3 ps i.

e. Air temperature sens or Ta – Sens or Ta will prevent compres s or s tart-up

if the air flowing through the unit is below 55

F. The s ensor will als o

prevent the compres s or s tartup or discontinue compres s or operation if

the air temperature is above 140

F and will res et at 135

F. A flas h code

of 4 will be initiated on the red diagnos tic LED 15.

f. Water temperature s ensor Tw – Sensor Tw will prevent compress or s tart-

up and trip an alarm (a flas h code of 3) if the outgoing fluid temperature
is above 125

F and will res et the alarm at 120

F. The s ens or will als o

trip at s tartup and during operation if the water temperature is below
55

F and will reset at 60

F.

g. Refrigerant temperature s ens or Tr – Sens or Tr will prevent compres s or

s tart-up if the coil temperature is below 40

F and res ets  at 65ᵒF.  A flas h 

code of 2 will be initiated on the red diagnos tic LED 15.

Any of the above faults will be indicated via the diagnos tic LED and the

appropriate diagnos tic flas h code. Pleas e note the temperatures provided

might vary by ±5

F.

Summary of Contents for SKC-008

























Reviews: