3-44
CFMOTO
●
Turn the ignition switch on and measure roll-over
sensor power source voltage.
Roll-over Sensor
Roll-over Sensor Output Voltage
:
Standard:12V DC (Battery voltage)
●
Turn the ignition switch OFF
«
If the reading of input voltage is less than the
standard, check the ECU for its ground, power sup-
ply and wiring shorted.
«
If the wiring is normal, check roll-over sensor
resistance.
●
Remove adapter and use the silicon glue to cover
and seal it.
●
Remove the sensor [G] (see Roll-over Sensor
Removal).
●
Connect a hand tester [A] to the connector [B]
with needle adapter set [D].
Roll-over Sensor Output Voltage
Meter
(+)
→
Gr/B [E]
Meter
(-)
→
L/G [F]
Roll-over Sensor Output Voltage Inspection
(when tilted)
●
Hold the sensor vertically.
●
Turn the ignition switch ON, and measure the
output voltage with the connector joined.
●
Tilt the sensor 40~50 degree or more [C] right or
left, then and measure the output voltage.
Sensor output voltage
Standard
:
0
~
0 . 5 V
Tilt the sensor right or left 55-75 degree or
more.
NOTE
●
If you need to test again, turn the ignition switch
OFF, and then ON.
●
Turn the ignition switch OFF.
●
Remove the needle adapter set, and apply sili-
cone sealant to the seals of the connector for
waterproofing.
«
If the output voltage is normal, the wiring is suspect.
Check the wiring.
«
If the wiring is good, check the ECU for its ground
and power supply (see ECU Power Supply
Inspection).
«
If the output voltage is out of the specified, replace
the roll-over sensor.
Summary of Contents for CF400-A 2017
