background image

10 Tire and rim

 

10

10-13

Tire Pressure Inspection/Adjustment

Ÿ

Refer to the Air Pressure Inspection in the Periodic Maintenance chapter.

Ÿ

Refer to the Wheel/Tire Damage Inspection in the Periodic Maintenance

chapter.

Tire Removal

Ÿ

Remove

Wheel (see Front/Rear Wheel Removal)

Valve Core (Let out the air)

Ÿ

To maintain wheel balance, mark the valve stem

position on the tire with chalk so that the tire can

be reinstalled in the same position.

Chalk Mark or Yellow Mark [A]

Air Valve [B]

Align [C]

Ÿ

Lubricate the tire beads and rim fl anges on both

sides with a soap and water solution or rubber

lubricant. This helps the tire beads slip off the rim

flanges.

Ÿ

Remove the tire from the rim using a suitable

commercially available tire changer.

  

NOTE

The tires cannot be removed with hand tools

because they fit the rims too tightly.

Tire Installation

Ÿ

Inspect the rim and tire, and replace them if necessary.

Ÿ

Clean the sealing surfaces of the rim and tire, and

smooth the sealing surfaces of the rim with a fine
emery cloth if necessary.

Ÿ

Remove the air valve and discard it.

 

Warning

 

Do not use engine oil or petro element to 
lubricate. Because it will damage the 
tires. 

   

 

 
 

 

Dangerous

 

Use same supplier

s tire in front and rear 

wheels.

 

 
 

 
 
 

Warning

 

Replace the air inject valve together with 

the tire. Do not reuse the air inject valve. 

 

Summary of Contents for CF400-A 2017




























































































































































































































































































































































































































































Reviews: