Centrometal BioTec Plus 25 Technical Instructions Download Page 45 | Manualshive

Page: 45 / 130

Centrometal BioTec Plus 25 Technical Instructions Download Page 45

Fuses

- lambda probe power supply

IMPORTANT:

When replacing a fuse, be sure turn off the boiler at the main switch and
unplug the power cord.

Note: Be sure to use proper acting fuses M (M = Medium)!

MARK

FUSE

DEVICES

F1

3,15 A, M

Lambda -

PCB

6.3. BOILER OPERATION PROCEDURE

The boiler is controlled with electronic control unit, built in the upper part of the boiler, below upper
casing.
Control unit controls boiler functioning, one heat circuit through 3 way mixing valve with actuator and
outdoor temp. sensor and DHW tank. On the front boiler panel are main switch, for switching on/off
the boiler control unit, safety thermostat and touch screen of control unit.

- Screw reﬁll
- electromagnetic valve

- Feeder screw motor device
- Rotary valve (RSE)
- grate cleaner motor
- Automatic ﬂue gas tubes cleaning
(Flue pass. Cleaner)

PCB

: 51229XXXXXXX

MARK

FUSE

DEVICES

F1

3,15 A, M

F2

1 6

, A, M

- electric heater

F3

3 15

,

A, M

PCB:

BIOPELTEC-D-G (

51229

XXXXXXX

"G"

)

MARK

FUSE

DEVICES

F1

3,15 A, M

F2

3,15 A, M

- Screw reﬁll
- electromagnetic valve
- Feeder screw motor device
- Rotary valve (RSE)
- grate cleaner motor
- Automatic ﬂue gas tubes cleaning
(Flue pass. Cleaner)
- electric heater

-

Technical instructions

BioTec Plus

45

«
...
43
44
45
46
47
...
»

Summary of Contents for BioTec Plus 25



































































































































Reviews:

No comments