manualshive.com logo in svg

Centrometal BioTec Plus 25, Technical Instructions, Page: 123 / 130

Share
Download
Centrometal BioTec Plus 25 Technical Instructions Download Page 123

WOOD FIRING ERRORS: 

ERROR

NAME

DESCRIPTION

Ew21

Firebox sensor

Boiler status: 

Boiler work normally.

Intervention mode:

 Boiler work to content heating demand 

but boiler has reduced possibilities.

Possible causes

:

 

Invalid firebox sensor.

WOOD PELLETS FIRING ERRORS: 

Ep31

Photocell error

Ep32

Safety pressure switch

Ep33

No flame in ignition phase

Ep34

Flame disappeared 
working phase

Ep35

Error grate cleaner

Ep36

Fuel level

Ep37

Flame disappeared at 
ignition stage

ERROR

NAME

DESCRIPTION

Boiler status:

 Boiler go to phase OFF after ending phase 

S0 (retry start is allowed).

Possible cause:

 Invalid photocell (sending information

that flame exist in phase S0).

Boiler status: 

Boiler immediate go to phase OFF.

Possible causes: 

Firebox resistance is too high in phases

S2, S3, S4, (S5). It’s open any door or opening on boiler.
Interruption  in  el.  connection  between  safety  pressure 
switch and boiler, connection to the boiler, cold connection 
or invalid safety pressure switch. Interruption or bad sealing 
of safety pressure switch pipe.

Boiler status: 

Boiler immediate go to phase OFF.

Boiler status: 

Boiler immediate go to phase OFF.

Boiler status: 

Boiler immediate go to phase OFF.

Boiler status: 

Boiler go to phases S7, C0 and OFF.

Boiler status: 

Boiler immediate go to phase OFF.

Ep38

Flame disappeared 
stabilization stage

Ep39

Fuel sensor

Boiler status: 

Boiler immediate go to phase OFF.

Boiler status: 

Boiler immediate go to phase OFF.

Ep40

Error flap not closed

Boiler status:

 Boiler work normally.

Possible causes:

 Check if the flap is blocked with pellets , if 

the sensor is soiled with dust , if the sensor is about 1 mm 
distant from the flap , if the sensor reacts on the flap (the 
LED lamp is switching on the sensor ).

Error list

Technical instructions

 BioTec Plus

123

Summary of Contents for BioTec Plus 25



































































































































Reviews:

No comments