CEN-TECH 62120 Owner'S Manual & Safety Instructions Download Page 7

Page: 7 / 40

Page 7

For technical questions, please call 1-888-866-5797.

Item 62120

I/M Monitors

Inspection and Maintenance diagnostic tests that the Control Modules

perform on specific sub-systems of the vehicle.
There are two types of Monitors:

•

Continuous:

Monitors that

perform tests all the time while

the engine is running.

•

Non-Continuous:

Monitors that require

specific operating conditions to be met

during a Drive Cycle in order for the

Monitors to run their testing sequences.

Note:

Not all Monitors are

supported by all vehicles.

Gasoline Engine Monitors

Continuous
MIS

- Misfire

FUEL

- Fuel System

CCM

- Comprehensive Components

Non-Continuous
CAT

- Catalyst

HCAT

- Heated Catalyst

EVAP

- Evaporative System

AIR

- Secondary Air System

O2S

- Oxygen Sensors

HTR

- Oxygen Sensor Heater

EGR

- EGR System

Diesel Engine Monitors

Continuous
MIS

- Misfire

FUEL

- Fuel System

CCM

- Comprehensive Components

Non-Continuous
HCCAT

- NMHC Catalyst

NCAT

- NOx Aftertreatment

- Boost Pressure System

EGS

- Exhaust Gas Sensor

- PM Filter

EGR

- EGR System

Summary of Contents for 62120









































Search results

Summary of Contents for 62120

Reviews:

Related manuals for 62120

Brands by name

Popular brands

CEN-TECH 62120, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for 62120

Reviews:

Related manuals for 62120

Brands by name

Popular brands