CEN-TECH 62120 Owner'S Manual & Safety Instructions Download Page 30

Page: 30 / 40

Page 30

For technical questions, please call 1-888-866-5797.

Item 62120

On-Board Monitor Test

Mode $06 Request On-Board Monitoring Test

Results for Specific Monitored Systems

View test data for Non Continuous Monitors.

This section contains advanced

functions. Some data may need to be

interpreted by a qualified technician.
Note:

Not all vehicles return the

same data, results may vary from

the examples given herein.
1. From

Diagnostic Menu

, select

On-Board Mon. Test

, then press

OK.

Diagnostic Menu 7/11

Read Codes

02 Monitor Test

Erase Codes

Live Data

View Freeze Frame

I/M Readiness

On-Board Mon. Test

Figure BJ

2. Select vehicle manufacturer.

Vehicle Manufacturer 1/28

BUICK

BMW

CADILLAC ?

CHEVROLET

CHRYSLER

FORD

Figure BK

3. Select and view Monitors, their

tests and results as needed.

On-Board

Mon.

Test

1/10

A/F Sensor Bank Sensor 1

H02S Bank Sensor 2

Catalyst Mon. Bank 1 ?

EVAP

EGR Heater Mon.B1S2

Misfire

Figure BL

Note:

If necessary, have a qualified

technician Interpret the data.

Summary of Contents for 62120









































Search results

Summary of Contents for 62120

Reviews:

Related manuals for 62120

Brands by name

Popular brands

CEN-TECH 62120, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for 62120

Reviews:

Related manuals for 62120

Brands by name

Popular brands