CEN-TECH 62120 Owner'S Manual & Safety Instructions Download

Page: 8 / 40

Page 8

For technical questions, please call 1-888-866-5797.

Item 62120

Diagnostic Test Modes

Diagnostic Test Modes as described in the latest OBD II standard SAE J1979.

Note:

Not all Modes are

supported by all vehicles.

$01

- Request Current Powertrain

Diagnostic Data

$02

- Request Powertrain

Freeze Frame Data

$03

- Request Emission-Related

Stored DTCs

$04

- Clear/Reset Emission-Related

Diagnostic Information

$05

- Request Oxygen Sensor Monitoring

Test Results (2007 and older vehicles only)

$06

- Request On-Board Monitoring Test

Results for Specific Monitored Systems

$07

- Request Emission-Related

Stored DTCs Detected During Current

or Last Completed Driving Cycle

$08

- Request Control of On-Board

System, Test or Component

$09

- Request Vehicle Information

$0A

- Request Emission-Related

Permanent DTCs

Summary of Contents for 62120









































Search results

Summary of Contents for 62120

Reviews:

Related manuals for 62120

Brands by name

Popular brands

CEN-TECH 62120, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for 62120

Reviews:

Related manuals for 62120

Brands by name

Popular brands