CEN-TECH 62120 Owner'S Manual & Safety Instructions Download

Page: 19 / 40

Page 19

For technical questions, please call 1-888-866-5797.

Item 62120

Read Trouble Codes

Modes $03, $07 and $0A Request Emission-Related DTCs

1. From

Diagnostic Menu,

select

Read Codes,

then press

OK.

Diagnostic Menu 1/11

Read Codes

Erase Codes

Live Data

View Freeze Frame

I/M Readiness

02 Monitor Test

On-Board Mon. Test

Figure U

Read Codes

1. From

Read Codes,

select from:

Stored Codes

Mode $03

Pending Codes

Mode $07

Permanent Codes

Mode $0A

This mode is available on

some vehicles starting in

2010 and is required on all

2012 and newer vehicles.

2. If there are no DTCs, the

message

“No codes are stored

in the module”

will appear.

3. View the DTC.

1/1

P0113

$10 Generic

Intake Air Temperature

Sensor 1 Circuit High

DTC

Control Module

DTC Description

Figure V

4. See

“DTC Lookup” on page 20

to view likely causes for DTCs.

Note:

To view operational data stored when

the DTC was stored, see

View Freeze Frame Data on page 28.

Summary of Contents for 62120









































Search results

Summary of Contents for 62120

Reviews:

Related manuals for 62120

Brands by name

Popular brands

CEN-TECH 62120, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for 62120

Reviews:

Related manuals for 62120

Brands by name

Popular brands