manualshive.com logo in svg

Cedar Summit Sedona F25035, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Sedona F25035 Installation And Operating Instructions Manual Download Page 78

 

78 

[email protected]

Hardware

6 x 

#8 x 1-3/8” Wood Screw

2 x 

#8 x 2-1/2” Wood Screw

A:

  With 2 people on the ground and at least 1 person in the fort, lift Small Roof Assembly up and over the Back 

side of the fort.  Guide the Small Roof Assembly onto the fort so it slides under the Mid Roof Support Assembly  

and the (2788) Mid Roof Supports sit tight to the siding on the Small Roof Assembly.  The front of the Small Roof 

Assembly should be flush to the front of each (2759) Roof End.   (fig. 33.1 and 33.2)

B: 

 Attach Small Roof Assembly to Mid Roof Support Assembly from inside with 3 (S20) #8 x 1-3/8” Wood 

Screws per side.  Screws to go into (2788) Mid Roof Supports.  (fig. 33.1)

C: 

 Measure 2-1/4” in from Roof Ends and attach Small Roof Assembly to the (2759) Roof End with 1 (S3) #8 x 

2-1/2” Wood Screw per side. (fig. 33.2 and 33.3)

x 3 per side per 

Roof Assembly

Tight

Small Roof 

Assembly

Step 33:  Attach Small Roof Assembly to Fort

Fig. 33.2

Fig. 33.1

S20

2788

Mid Roof Support Assembly

2759

2759

Small Roof 

Assembly

S3

Fig. 33.3

S3

Flush

S3

2¼”

S20

2759

Flush

Summary of Contents for Sedona F25035
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands