manualshive.com logo in svg

Cedar Summit Sedona F25035, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Sedona F25035 Installation And Operating Instructions Manual Download Page 76

 

76 

[email protected]

Step 31:  Attach Long Roof Ends

A:

  Place 1 (2793) Long Roof End tight to each (2788) Mid Roof Support and flush to the top of (2818) Transom 

Window.  Make sure (2793) Long Roof End is level and the overhang at each end meaures 4-7/8”, then attach to 

(2788) Mid Roof Supports with 1 (S3) #8 x 2-1/2” Wood Screw and 1 (S4) #8 x 3” Wood Screw per support and 

to each side of the (2818) Transom Windows using 2 (S3) #8 x 2-1/2” Wood Screws per side.  (fig. 31.1)

B:

  Fasten (2788) Mid Roof Support to both (2818) Transom Windows using 1 (S3) #8 x 2-1/2” Wood Screw per 

side.   (fig. 31.2)

Fig. 31.1

2 x 

Long Roof End 1-1/4 x 3 x 18-3/4”

Wood Parts

Hardware

2793

8 x 

#8 x 2-1/2” Wood Screw

2 x 

#8 x 3” Wood Screw

S3

Fig. 31.2

Flush

Flush

2788

2818

2818

2793

S4

4-7/8”

S3

S3

S4

S3

2793

2788

2818

2788

S3

Summary of Contents for Sedona F25035
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands