manualshive.com logo in svg

Cedar Summit Sedona F25035, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Sedona F25035 Installation And Operating Instructions Manual Download Page 67

 

67 

[email protected]

Large Roof 

Assembly

Gable Dormer 

Assembly

Front

Gable Dormer 

Assembly

Step 27:  Attach Gable Dormer to Roof

S11

Fig. 27.2

Fig. 27.3

Hardware

Wood Parts

4 x 

#8 x 2” Wood Screw

S11

1 x 

Dormer Cleat 1-1/4 x 3 x 12-3/4”

2688

A:

  On the outside of the Large Roof Assembly on (2644) Front Roof Panel, on the 5th siding down, place (2688) 

Dormer Cleat centred on the panel (over the middle inside slat) then attach with 2 (S11) #8 x 2” Wood Screws.  

Make sure the screws go into the siding and the slats.  (fig. 27.1)

B:

  Place completed Gable Dormer Assembly over (2688) Dormer Cleat and attach with 2 (S11) #8 x 2” Wood 

Screws  (fig. 27.2 and 27.3)

A

DWG.  NO.

SIZE

WEIGHT: 

Dormer Roof Prep

SHEET 3 OF 3

REV.

SCALE:1:50

Fig. 27.1

5th 

Siding

2688

S11

Large Roof 

Assembly

Inside slat

2644

Summary of Contents for Sedona F25035
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands