manualshive.com logo in svg

Cedar Summit Sedona F25035, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Sedona F25035 Installation And Operating Instructions Manual Download Page 71

 

71 

[email protected]

Fig. 28.10

E:

  On the Back of the fort measure 21-5/8” from (2759) Roof End and 1-1/4” down from the top of (2677) Narrow 

Panel, pre-drill with a 3/16” drill bit then place 1 (2684) Mid Roof End centred over the pilot hole and flush to the top 

of (2677) Narrow Panel attach from the inside with 1 (S4) #8 x 3” Wood Screw and from the outside with 1 (S3) #8 x 

2-1/2” Wood Screws. (fig. 28.9 and 28.10)

F:

  On the Front of the fort measure 21-5/8” from (2759) Roof End and 1-1/4” down from the top of the panel, pre-

drill with a 3/16” drill bit then place 1 (2684) Mid Roof End centred over the pilot hole and flush to the top of the 

(2677) Narrow Panel and attach from the inside with 1 (S4) #8 x 3” Wood Screw and from the outside with 1 (S3) #8 

x 2-1/2” Wood Screws. (fig. 28.12 and 28.11)

Step 28:  Attach Roof Ends 

Part 4

Flush

Flush

Front Wall

Fig. 28.11

2677

2759

Fig. 28.9

2684

2684

2677

2677

2684

2759

Flush

Flush

Back Wall

Hardware

2 x 

Mid Roof End 1-1/4 x 4-7/8 x 7”

Wood Parts

2684

2 x 

#8 x 2-1/2” Wood Screw

2 x 

#8 x 3” Wood Screw

S3

S4

S3

S3

S4

S4

2677

2684

21-5/8”

21-5/8”

Front 

Wall

Back 

Wall

End Wall

Fig. 28.12

Summary of Contents for Sedona F25035
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands