manualshive.com logo in svg

Cedar Summit Sedona F25035, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Sedona F25035 Installation And Operating Instructions Manual Download Page 20

 

20 

[email protected]

Step 2: End Wall Prep 

Part 2

It is important to assemble the frame on a flat, smooth surface.

D:

  Turn the assembly over then attach top and middle boards with 4 (H9) 1/4 x 1-1/4” and bottom board (2769) 

Panel Frame with 2 (H10) 1/4 x 2-1/4” Hex Bolts (with lock washer and flat washer) connecting to the previously 

installed t-nuts.  (fig. 2.3 and 2.4)

E:

  Place 1 (2778) SW Ground MOD to each side of (2769) Panel BT Frame, notice the hole locations and attach 

with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer and flat washer) per board connecting to previously installed 

t-nuts.  (fig. 2.3 and 2.5)

H:

  Place 1 (2607) Diagonal under (2778) SW Ground MOD on the side of (2771) End Post Left.  Loosely attach 

with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer, flat washer and t-nut).  (fig. 2.3 and 2.5)

Fig. 2.4

Fig. 2.3

2768

2769

H9

x 2 per board

FW1

LW1

H9

2769

2771

2770

x 2 per board

H9

Fig. 2.5

Note which bolt holes are used

2778

2778

2769

4 x 

1/4 x 1-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer)

3 x 

1/4 x 2-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer and 1 1/4” t-nut)

2 x 

SW Ground MOD 5/4 x 4 x 14-1/4”

1 x 

Diagonal 1-1/4 x 3 x 22”

H9

Wood Parts

Hardware

2778

2607

H10

2778

2778

H10

2607

H10

LW1

FW1

TN1

Summary of Contents for Sedona F25035
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands