manualshive.com logo in svg

Cedar Summit Sedona F25035, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Sedona F25035 Installation And Operating Instructions Manual Download Page 28

 

28 

[email protected]

E:

  On the Front Wall, from inside the assembly, 

tight to the End Wall, halfway up the assembly, 

5/8” down from the top of the panel board attach 

1 (2777) Side Joist MOD to (2677) Narrow 

Panel and (2772) Panel Floor Support  with 2 

(H11) 1/4 x 2-3/4” Hex Bolts (with lock washer, 

flat washer and t-nut).  Bolts are installed from 

inside the assembly.  Make sure (2777) Side 

Joist MOD is level then attach with 4 (S3) #8 x 

2-1/2” Wood Screws.  (fig. 4.9 and 4.10)

F:

  Tight to (2777) Side Joist MOD, 5/8” down 

from the top of the panel board attach (2682) 

Short Side Joist to (2772) Panel Floor Support 

with 1 (H11) 1/4 x 2-3/4” Hex Bolt (with lock 

washer, flat washer and t-nut).  Bolt is installed 

from inside the assembly.  Make sure (2682) 

Short Side Joist is level and flush to the top of 

(2777) Side Joist MOD then attach with 2 (S3) 

#8 x 2-1/2” Wood Screws.  (fig. 4.9 and 4.10)

G:

  Repeat E and F for the Back Wall, except 

(2777) Side Joist MOD is tight to the Swing Wall 

and (2682) Short Side Joist is attached to (2677) 

Narrow Panel.  (fig. 4.9 and 4.10)

12 x 

#8 x 2-1/2” Wood Screw

6 x 

1/4 x 2-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

Hardware

Top View

S3

2 x 

Side Joist MOD 2 x 2 x 40-1/4”

2 x  

Short Side Joist 2 x 2 x 22-1/8”

Wood Parts

2777

2682

Tight

2777

(hidden)

(hidden)

2677

H11

Fig. 4.10

Fig. 4.9

S3

S3

H11

H11

S3

2677

2777

2772

2772

2682

2682

Back 

Wall

Front Wall

2682

2677

2677

2772

2772

2682

2777

2622

H11

2777

Tight

Step 4: Frame Assembly 

Part 4

End Wall

FW1

LW1

TN1

5/8”

Swing Wall

S3

S3

Back Wall

Front Wall

Summary of Contents for Sedona F25035
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands