manualshive.com logo in svg

Cedar Summit Sedona F25035, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Sedona F25035 Installation And Operating Instructions Manual Download Page 22

 

22 

[email protected]

Step 3: Swing Wall Prep 

Part 2

It is important to assemble the frame on a flat, smooth surface.

C:

  Turn the (2757) LT Post Assembly and (2758) RT Post Assembly over and place 2 (2756) Siding Assemblies 

on top so one sits flush with the top of the middle groove and the second fits flush with the top of the bottom 

groove.  (fig. 3.2 and 3.3) 

D:

  Place (2630) SW Top in the top grooves, (2768) Panel Floor in the middle grooves and (2769) Panel BT 

Frame in the bottom grooves so they sit flush to the outside edges of (2757) LT Post Assembly and (2758) RT 

Post Assembly.  Make sure the assembly is square then attach with 4 (S30) #8 x 1-1/16” Wood Screws per 

board.   (fig. 3.4). 

S30

2756

Wood Parts

Hardware

2768

2769

2630

Fig. 3.2

Bottom

Top

Flush

2758

2756

2757

2756

Fig. 3.3

Flush

Flush

2757

2758

S30

x 4

S30

x 4

S30

x 4

2768

2630

2769

Fig. 3.4

Notice Orientation of both 

(2756) Siding Assemblies.

Top

2 x 

Siding Assembly 1-1/4 x 19-15/16 x 39-3/16”

1 x  

SW Top 1-1/4 x 5-1/2 x 42”

1 x 

Panel Floor 1-1/4 x 3 x 42”

1 x 

Panel BT Frame 1-1/4 x 3 x 42”

12 x 

#8 x 1-1/16” Wood Screw

Summary of Contents for Sedona F25035
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands