manualshive.com logo in svg

Cedar Summit Sedona F25035, Installation And Operating Instructions Manual

Share
Download
Cedar Summit Sedona F25035 Installation And Operating Instructions Manual Download Page 30

 

30 

[email protected]

4 x 

1/4 x 3” Lag Screw (1/4” flat washer)

2 x 

1/4 x 2-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

Hardware

I:

  On the End Wall, place (2607) Diagonal beneath (2778) SW Ground MOD and attach with 1 (H10) 1/4 x 2-1/4” 

Hex Bolt (with lock washer, flat washer, and t-nut).  (fig. 4.13, 4.14)

J:

  On the Swing Wall, place (8587) Diagonal beneath (2824) Diagonal Support and attach with 1 (H10) 1/4 x 2-1/4” 

Hex Bolt (with lock washer, flat washer, and t-nut). (fig. 4.15, 4.16) 

K:

  Place (2607) Diagonal tight and flush to the front of the End Wall then pre-drill pilot holes with a 3/16” drill bit and 

attach each (2607) Diagonal to the End Wall with 1 (LS3) 1/4 x 3” Lag Screw (with flat washer) per board, checking 

that they remain flush to outside edge.  (fig. 4.13, 4.14) 
 

L:

  Place (8587) Diagonal tight and flush to the front of the Swing Wall then pre-drill pilot holes with a 3/16” drill bit 

and attach (8587) Diagonal to the Swing Wall with 1 (LS3) 1/4 x 3” Lag Screw (with flat washer) per board, checking 

that they remain flush to outside edge.  (fig. 4.15, 4.16) 

TIGHTEN ALL BOLTS

LS3

Fig. 4.13

Fig. 4.15

Step 4: Frame Assembly 

Part 6

End Wall

Tight

LS3

2607

2607

FW1

Swing Wall

8587

8587

LS3

FW1

LS3

LS3

H10

H10

H10

H10

2607

1 x 

Diagonal 2 x 3 x 42-1/4”

1 x  

Diagonal 1-1/4 x 3 x 22”

Wood Parts

8587

2607

H10

Fig. 4.14

Fig. 4.16

2607

2824

8587

FW1

LW1

TN1

FW1

LW1

FW1

TN1

LS3

FW1

LS3

Summary of Contents for Sedona F25035
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands