manualshive.com logo in svg

Cary Audio Design HD Surround Sound Processor Cinema 11a, Owner'S Manual

Share
Download
Cary Audio Design HD Surround Sound Processor Cinema 11a Owner'S Manual Download Page 7

WELCOME 

 

 

6

THANK YOU 

 

Congratulations on becoming a Cinema 11a owner! 

 

We, at Cary Audio Design, would like to thank you for purchasing the new Cinema 11a HD 

Surround Sound Processor. The Cinema 11a is the latest generation in our line of award-winning 

surround sound processors.  

 

The Cinema 11a is the ultimate in surround sound processors. Utilizing the Cirrus Logic CS49700 
series chipset and HDMI v1.3 inputs, the Cinema 11a has the ability to properly decode and 

playback both the raw bitstream and lossless linear PCM signals from the latest high resolution 

formats, including Dolby True HD, Dolby Digital Plus, DTS-HD Master Audio, and DTS-HD High 

Resolution Audio. The Cinema 11a has the ability to set separate Listener Profile speaker settings 

for playback of Music and Movies. The Cinema 11a uses the absolute highest quality components 

available within the audio circuit, resulting in extraordinary sound quality, which is a known 
trademark of Cary Audio Design products. The Cinema 11a also contains an HD radio tuner for 

the highest resolution signals from FM broadcasts.  

 

The Cinema 11a was designed for ease of use whether in normal home surround sound systems 

or in more complex custom installations. It has an independent 2

nd

 zone so you can experience 

surround sound in your main home theater room as well as 2

nd

 zone stereo sound in a different 

location. A separate 2

nd

 zone remote handset comes standard with the Cinema 11a so full control 

of the input source selection in each of the two zones is at your fingertips. 

 

All Main zone audio output connectors have 24 bit/192 kHz D/A converters operating in dual 

differential mode for excellent sound quality and high dynamic range. In addition, the Cinema 
11a includes 7.1 channel XLR balanced audio outputs for the Main zone if you are using a power 

amplifier equipped with balanced input connections.  

 

The Cinema 11a was designed to remain viable in a future of rapidly emerging and changing 

digital technologies. It has a rear panel RS-232 serial port connector that provides for home 

automation serial control, and also allows us to provide flash memory upgrades.  
 

We firmly believe in high performance products that offer incredible value for the money. With its 

leading edge technology, exceptional sound performance and ease of use, the Cinema 11a is 

without question, the highest performing surround sound processor available today.  

 

Thank you for your continued support and enjoy your Music and Movies! 
 

 

The Cary Audio Design Team 

Summary of Contents for HD Surround Sound Processor Cinema 11a




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands