Cary Audio Design HD Surround Sound Processor Cinema 11a Owner'S Manual Download Page 51

Page: 51 / 59

SETUP MENU

Press the

button on the remote to reach “BACK” then press the ENTER button on the

remote to return to the “PASSWORD” menu, or press the SETUP button on the remote to
exit the “SETUP MENU” completely.

MASTER VOLUME

Please follow steps 1 through 3 from the “to set password” instruction above to reach the
“ADVANCED SETTINGS” menu.

Once you have entered the “ADAVANCED SETTINGS” menu, press the

button on the

remote until you reach “MASTER VOLUME” on the front panel display.

The “ADVANCED SETTINGS / MASTER VOLUME……-30dB” menu appears on the front
panel display.

Use the

and

buttons on the remote to adjust the Master Volume from -90dB to

+15dB. This is the preset Master Volume level that the unit will power on to and default

to upon switching to a new input for the first time after power on.

HDMI AUDIO OUT

Please follow steps 1 through 3 from the “to set password” instruction above to reach
the “ADVANCED SETTINGS” menu.

Press the

button on the remote until you reach “HDMI AUDIO OUT” on the front

panel display.

The “ADVANCED SETTINGS / HDMI AUDIO OUT….Off” menu appears on the front
panel display.

Use the

and

buttons on the remote to select the “OFF” or “ON” mode. When you

select the “OFF” mode, the HDMI output connector

will not output audio data. When

you select the “ON” mode, the HDMI output connector

will output the native audio

data as it is being received from the source device.

AV SYNC DELAY

Please follow steps 1 through 3 from the “to set password” instruction above to reach the

“ADVANCED SETTINGS” menu.

Press the

button on the remote until you reach “AV SYNC DELAY” on the front panel

display.

The “ADVANCED SETTINGS / AV SYNC DELAY” menu appears on the front panel display.

Use the

and

buttons on the remote to select the “OFF” mode or set an AV Sync

Delay time between 1ms to 100ms. This feature is useful in large rooms or with a DVD

player that up-converts video to higher resolutions like the DVD 7 which offers 1080p
video outputs.

Summary of Contents for HD Surround Sound Processor Cinema 11a




























































Search results

Summary of Contents for HD Surround Sound Processor Cinema 11a

Reviews:

Related manuals for HD Surround Sound Processor Cinema 11a

Brands by name

Popular brands

Cary Audio Design HD Surround Sound Processor Cinema 11a, Owner'S Manual

Search results

Summary of Contents for HD Surround Sound Processor Cinema 11a

Reviews:

Related manuals for HD Surround Sound Processor Cinema 11a

Brands by name

Popular brands